Jump to content
xisto Community
Chesso

Flash 8/actionscript 2, Platform Game (little Help).

Recommended Posts

Hello, I have been following along with the tutorial here:

https://www.kirupa.com/developer/mx2004/platform_game.htm

I am basically at the point of having the ball/character fall onto the blocks within the ground/platform movie clip, movie left and right, jump up and down etc.

So far this is all very good, except for one very annoying thing lol, which has pretty much halted me from continuing any further (heck I even tried searching google for the lats couple of hours but can't find any relevant hits to my specific case).

If anyone has followed this, understands it's method of play and collision detection or has followed this before will more than likely know my problem, which is:

When the ball/character jumps/falls onto a block, the collision detection is quite random, sometimes it falls a bit too far above, sometimes exact, sometimes inside (I move the balls movie clip point upward so the crosshair was below the image for somewhat better detection).

Does anyone have a solution for this?

I know I could create singular platformed objects and test them individually using the old basic co-ordinate checks, but being able to have multiple platforms of the same type all sitting in the same movie clip and all subject to the exact same collision call is extremely usefull and removes alot of bloated code.

Any help is greatly appreciated! ;).

Share this post


Link to post
Share on other sites

Hello, I have been following along with the tutorial here:
https://www.kirupa.com/developer/mx2004/platform_game.htm

I am basically at the point of having the ball/character fall onto the blocks within the ground/platform movie clip, movie left and right, jump up and down etc.

So far this is all very good, except for one very annoying thing lol, which has pretty much halted me from continuing any further (heck I even tried searching google for the lats couple of hours but can't find any relevant hits to my specific case).

If anyone has followed this, understands it's method of play and collision detection or has followed this before will more than likely know my problem, which is:

When the ball/character jumps/falls onto a block, the collision detection is quite random, sometimes it falls a bit too far above, sometimes exact, sometimes inside (I move the balls movie clip point upward so the crosshair was below the image for somewhat better detection).

Does anyone have a solution for this?

I know I could create singular platformed objects and test them individually using the old basic co-ordinate checks, but being able to have multiple platforms of the same type all sitting in the same movie clip and all subject to the exact same collision call is extremely usefull and removes alot of bloated code.

Any help is greatly appreciated! :ph34r:.

You should slow down the gravity speed and speed up the fps. To change the frame speed just right click and change the properties.

Share this post


Link to post
Share on other sites

Yeah of course, I always have it at 30 FPS.I'm familiar with Object Pascal/DirectX programming so I'm not new to concept such as frames per second, depth, collision detection, enemy AI etc.Mostly just grasping how flash and actionscript goes about things.

Share this post


Link to post
Share on other sites

was following that tutorial for a while, but then the code he gave me had unexpected errors.I pasted the exact code over and over again, but it always had a syntax error.do I need to get a new flash program?

Share this post


Link to post
Share on other sites

I have seen that tutorial before, but I have not analyzed how the code is structured... But the way that I make sure that things stop on the places that I want it to is to basically check if the object will pass the point which I wish for it to stop at, if it does I make it go directly to the place which I want it to... So what I do is create an if with the calculation, yes, I know it's a bit redundant but it works better than adjusting fps values and such... Here is an example:If(ourCharacter._x-walkSpeed < 0){ ourCharacter._x=0;}It could probably be used in conjunction with hittests... Just a question of trying it out.

Share this post


Link to post
Share on other sites

Answer

Flash 8/actionscript 2, Platform Game (little Help).

 

Well my conclusion is that it is a glitch. If you notice on the game hes made even that has collision detection problems. Youve made no mistake its just not a very good way to make the game. Soz who made it but it isnt.

 

-reply by rosssss

Share this post


Link to post
Share on other sites

Change path of Shared Object

Flash 8/actionscript 2, Platform Game (little Help).

 

Can anybody tell me how to change the path of shared object default path to any D or E drive..

 

E.G : Default path like

C:Documents and SettingsTempNameApplication DataMacromediaFlash Player#SharedObjectsD8F43EBDlocalhostTempFlash1.Swf

 

to

 

D:Sample

 

Plse reply

 

Thank you

 

 

-question by Harish

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...

Important Information

Terms of Use | Privacy Policy | Guidelines | We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.